Why Is C350L0 CHS Widely Used in Australian and New Zealand Structural Projects?

API 5L steel pipe

The C350L0 CHS standard is preferred by engineers in Australia and New Zealand because it includes a minimum yield strength of 350 MPa, impact testing at 0°C, and round-section efficiency all in one well-known package. As 1163 grade c350 l0 structural section comes with clear instructions that help builders pass checks and work with plans that follow AS 4100 and NZS 3404. Because it is round, it doesn’t bend in any direction, and it can be welded to columns, braces, trusses, and bridge members. I wrote this guide to help buyers understand the name, weigh their choices, and place an order with confidence.

IMG 20250313 111516 2 scaled内容7

What AS/NZS 1163 C350L0 CHS Means

How to Read the C350L0 Designation

AS/NZS 1163 talks about structural steel hollow sections that are cold-formed. The name C350L0 means “cold-formed,” “350” means “minimum yield strength” in megapascals, and “L0” means “Charpy impact requirement at 0°C.” For L0 grades, the standard says that the average impact energy must be at least 27 J. We have the C250, C250L0, C350, C350L0, C450, C450L0, and C550L0 in our product line. They are all made by the cold-formed ERW process and come in CHS form. A structural section made of 1163 grade C350 L0 is good for exposed steelwork where a sudden brittle fracture would be expensive and dangerous. This is because the L0 suffix adds a toughness check. It can be written on a drawing in one line.

Key Mechanical Values at a Glance

I look at the table to see what the lowest values are that I need to check when I read a specification. It is the same for L0 grades as it is for standard grades, but they also have to meet the 0°C impact requirement.

 
Grade Min. yield (MPa) Min. tensile (MPa) Impact requirement
C250 / C250L0 250 320 L0: 27 J at 0°C
C350 / C350L0 350 430 L0: 27 J at 0°C
C450 / C450L0 450 500 L0: 27 J at 0°C

AS/NZS 1163:2016 is the source.

Why Compliance Documents Matter

Checkers and owners of property don’t believe claims of compliance that aren’t backed up by proof. It is important to get an EN 10204 3.1 certificate that shows the grade, standard, heat number, chemistry, tensile results, and impact results. At LONGMA, each pipe can be tracked by its raw material control, heating no., batch no., and product no. This means that a certificate can be linked to a certain heat. There is also an ISO 9001 quality system that we follow. Before you send the material to the shop floor, compare the outside diameter and wall thickness to the standard’s tolerances. Also, check the paperwork to make sure it matches the most recent edition of the standard.

Structural Efficiency and Grade Comparison

Why Round Sections Work in Compression

A hollow section in the shape of a circle puts the steel at the same distance from the center on all axes. This means that the steel can turn and bend in any direction. That number is close to 0.35 times the outside diameter for a thin wall. CHS is a good choice for columns, braces, and truss chords that have to deal with changing load directions because it is stiff in all directions. The round surface doesn’t have a flat top where dirt and water can gather either. Joint rules for round nodes can be found in CIDECT Design Guide 1. Architects like how canopies, bridges, and stadiums look when the steel is left out in the open.

C350L0 Versus C250, C350, and C450L0

Choice grade strikes a balance between toughness, weight, and strength. The minimum yield goes up by 100 MPa when you go from C250 to C350. This means that for the same axial load, a compression member can often have a thinner wall. For members that will be exposed to the elements or live in cold places, the L0 suffix adds the 27 J impact check at 0°C. With C450L0, the minimum yield goes up to 450 MPa, which is better for heavy loads like mining conveyor gantries. However, fabricators should carefully look over their welding procedures. The as 1163 grade c350 l0 structural section is in the middle for many building and bridge members. It is strong enough to save steel and tough enough to be used outside.

Comparison with ASTM A500 and EN 10219 Tube

A lot of the time, project teams want to know about overseas round tube. The table shows comparisons of common round-section minimums. Because chemistry, tolerances, and test rules are different, substitution needs written engineering approval.

 
Product Min. yield Min. tensile Impact rule
AS/NZS 1163 C350L0 350 MPa 430 MPa 27 J at 0°C
ASTM A500 Grade C (round) 317 MPa (46 ksi) 427 MPa (62 ksi) No mandatory Charpy test
EN 10219 S355J0H 355 MPa (up to 16 mm wall) 470–630 MPa 27 J at 0°C

AS/NZS 1163:2016, ASTM A500/A500M-23, and EN 10219-1:2006 are the sources.

Why It Fits Australian and New Zealand Projects

A Standard Designers and Inspectors Know

As/NZS 1163 is a standard that both Australia and New Zealand agree on, so it can be used for products on both sides of the Tasman. Designers in Australia use AS 4100 to check steel members, while designers in New Zealand use NZS 3404. When an inspector sees the name C350L0 on a drawing, they already know what strength, impact test, and certificate are needed. The back-and-forth during acceptance is cut down by that shared language. AS/NZS 1163 is also used by owners in Southeast Asia, and it takes about 7 to 14 days for sea freight from China to get to those ports. It takes three to four weeks to ship to Australia and New Zealand.

Where C350L0 CHS Appears on Site

Building columns, braces, roof trusses, bridge members, towers, bollards, and equipment supports are all common uses. The L0 check is helpful for exposed members in cooler areas and for members that get hit or move around a lot. If there are heavy loads on conveyor gantries and walkways in mining, they may need C450L0. Custom lengths up to 18 m cut down on field butt welds. Inside diameters range from 114.3 mm to 1422 mm, wall thicknesses from 6.02 mm to 50.8 mm, and standard lengths range from 3 m to 12.5 m in our CHS range. This means that it can be used for both light frames and heavy infrastructure.

Coating and Corrosion Protection

The L0 rating talks about toughness, not resistance to corrosion, so places near the coast, in humid places, or in factories still need protection. Our as 1163 grade c350 l0 structural section can be used with systems that paint or hot-dip galvanize. AS/NZS 4680 says that galvanized work must have an average coating thickness of 85 µm on steel that is more than 6 mm thick, which includes walls that are at least 6.02 mm thick. For zinc to flow and air to escape, hollow parts need vent and drain holes. In harsh air, a two-part system (galvanizing and painting) makes things last longer. Tell the pipe and the coater about your exposure class and coating needs as soon as possible so that everyone works together on the same plan.

Sizing, Fabrication, and Installation

Choosing Diameter and Wall Thickness

Do not start with just the diameter. Instead, start with the full load case. Find out about the axial force, bending force, shear force, effective length, end restraint, and connection type. When the diameter gets bigger, the radius of gyration gets bigger, too. This makes it less likely for long compression members to buckle. Thick walls make things stronger and more stable, but they also make them heavier and cost more to ship. A few trial sizes usually show the best balance of steel weight and joint ease within the range that is available. Also, make sure you know how long a crane or truck can handle. Before you place the order, a qualified engineer must check the member, joint, and system levels for capacity.

Cutting, Welding, and Connection Details

With CNC tools, the C350L0 CHS cuts, drills, and profiles well. Most round-to-round nodes have saddle or fish-mouth cuts, and bolted splices are made with end plates or flanges. Welders should use the right consumables, keep the heat input under control, and check for distortion. For thicker walls, you might need preheat or interpass control, so go over the steps with your inspector. The first CIDECT Design Guide gives rules for all CHS nodes to follow. This ERW pipe has a clean surface finish and walls that are all the same thickness. This makes it easier to fit together. When parts are going to be galvanized, they need to have vent holes in the right places.

From Drawing to Site: A Simple Order Flow

For first-time buyers, this is how I think they should place their order.

Check the drawings and grade, then the certificate and tolerances, then place a trial order, inspect it when it arrives, and then release repeat orders. .

Most buyers start with a small order to make sure the sizes, welds, and paperwork are correct. Once the first group is done, orders that come up again move faster. At LONGMA, some stock pipes can be sent out as quickly as 7 days, while common sizes ship in 30 days and custom products ship in 45 days. It takes about three to four weeks for sea freight to get to Australia and New Zealand. Make sure you include the whole time on your critical path so that late steel doesn’t get fined.

Buying Certified C350L0 CHS Without Costly Mistakes

A Procurement Checklist for Certified Sections

These are the three things I want buyers to make sure of before I send anything out.

  • Specification: State the standard, edition year, grade, outside diameter, wall thickness, and length on the purchase order. Add the dimensional tolerances and pipe markings you expect, such as outside diameter within ±1% with a minimum of ±0.5 mm, so the supplier, inspector, and site team all work from one written definition.
  • Documents: Request an EN 10204 3.1 certificate for each heat, showing chemistry, tensile results, and the 0°C impact results. Match the heat number on the certificate to the number marked on every pipe before cutting or coating begins, and keep these records for building acceptance, later audits, and any warranty questions.
  • Total cost: Compare quotations after adding freight, duties, coating, storage, and lead-time risk. A low unit price loses its value if rejected material delays the program, forces a re-order, and adds a second shipment. Also ask what inspection and packing support the supplier offers for export, because damage in transit adds cost too.

When someone asks for a 1163 grade C350 L0 structural section, a short checklist makes it clear what needs to be done.

Common Mistakes to Avoid

Most people make the mistake of thinking that all C350 products are the same. They have to match in terms of grade, standard, impact class, size, and certificate. A plain C350 pipe does not have the L0 impact check. Some other mistakes people make are choosing a size based on the outside diameter without checking the wall thickness and slenderness, thinking that steel won’t rust without a coating, placing an order without checking the heat traceability and cut lengths, and not considering the shipping time. There is also acceptance risk when you mix overseas standards without getting engineering approval first. A written purchase order, a technical review, and a check before shipping take care of most of these issues.

Is C350L0 CHS Right for Your Project?

AS 1163 grade c350 l0 structural section is good for axial members, bracing, trusses, architectural steel, and outdoor supports that need to be round and have compliance documentation. That choice isn’t always the best one for every member. Even though we only make round sections, rectangular and square hollow sections can make flat-plate connections easier. Most of the time, universal beams are better at major-axis bending. Higher grades, like C450L0, can make things lighter, but they may also cost more and be harder to weld. Before you make your choice, look at these things: the code and loads, the environment, the shape and slenderness of the section, the connections, the coating, the certificates, the availability, and the engineer’s approval.

Conclusion

A lot of projects in Australia and New Zealand use as 1163 grade c350 l0 structural section because it has a minimum yield strength of 350 MPa, an impact check of 27 J at 0°C, and a round shape with equal stiffness. All of these features are covered by the same standard, AS/NZS 1163. Instead of C250, it saves steel. Compared to ASTM A500 round tube, it has an extra impact test that must be done, and it meets the toughness level of 0°C for EN 10219 S355J0H. Even if something is tough, it will still rust, so it needs to be coated. Also, galvanized metal needs vent holes and the right thickness of zinc. To get good results, the grade, size, connections, certificates, and delivery time must all match, and the final choice must be approved by an engineer.

FAQ

What is the difference between C250 and C350?

It takes at least 350 MPa of force to stretch C350, and it takes at least 430 MPa of force to pull it apart. The C250 has 250 MPa and 320 MPa. A stronger member can often hold the same amount of weight, though the final size is determined by design checks and connection details.

What is AS/NZS 1163 pipe?

There is a hollow structural section called AS/NZS 1163 for cold-formed structural steel hollow sections that this is made to. Our version is ERW pipe in the shape of a CHS, and it is used in building projects, bridges, infrastructure, mining, energy, and transportation. It comes in grades like C250, C350, and C450, and you can get it in L0 too.

What does L0 mean in C350L0?

It means that the steel passes a Charpy impact test at 0°C with an average energy of at least 27 J. It talks about toughness, not resistance to corrosion, so for outdoor use, you will still need to galvanize or paint it. For the EN 10204 3.1 certificate, ask for the results of the impact tests.

Get Your as 1163 grade c350 l0 structrual section Quote from LONGMA

Do you need a supplier of as 1163 grade c350 l0 structural section for a project? Since 2003, LONGMA has been making ERW and LSAW steel pipe. Each year, they make 500,000 tons of it, and they have EN 10204 3.1 and ISO 9001 certifications, as well as full traceability. Email us at info@ilongma.com with your size, grade, quantity, coating, and delivery port, and we’ll get back to you with a quote. For more information, go to ilongma.com.

Categories

Get Free Quote

Related Article​

Wechat ID: 008618661500134

Request Free Quote