Opens in a new tab

ASTM A691 2-1/4Cr Class 22 EFW Pipe: Specification, Sizes and Applications

ASTM A691/A691M covers carbon and alloy steel pipe that is electric-fusion-welded with filler metal added and manufactured from pressure-vessel-quality plate for high-pressure service at high temperatures. The 2-1/4Cr grade is a chromium-molybdenum alloy steel designation, while Class 22 identifies a specific combination of pipe heat treatment, weld radiography and pressure testing. These are separate parts of the designation and should be stated together in the purchase order.

微信图片 2023052915471612 1 scaledA691 PIPE 1 2

ASTM A691 2-1/4Cr Class 22 Specification

What the designation means

ASTM A691 identifies the product specification and manufacturing form: electric-fusion-welded carbon or alloy steel pipe made from pressure-vessel-quality plate, with filler metal added. The grade identifies the plate type listed by the specification. The 2-1/4Cr designation identifies the chromium-molybdenum grade associated with nominal 2.25% chromium and 1.00% molybdenum chemistry. Class 22 is not the material grade; it is the class designation that defines the pipe heat-treatment condition, radiographic examination and pressure-test requirements.

Plate material and chemistry

For 2-1/4Cr material, ASTM A387/A387M Grade 22 is a relevant chromium-molybdenum pressure-vessel plate specification. Its nominal alloy contents are 2.25% chromium and 1.00% molybdenum. The complete chemical and mechanical requirements must be taken from the plate specification and edition stated in the order and verified against the material test certificate. Do not infer compliance from the nominal alloy designation alone. The plate heat, pipe identification and test records should remain traceable through manufacturing.

What Class 22 requires

Under ASTM A691/A691M, Class 22 specifies stress-relief heat treatment, radiographic examination of the weld in accordance with Section 9, and the pressure test in accordance with Section 8.3. These requirements are distinct and all three should be reflected in the inspection and test plan. The applicable edition of the standard and any supplementary purchaser requirements must be stated in the order.

 
Class 22 item Requirement identified by ASTM A691/A691M
Heat treatment Stress relieved, see the applicable standard clause.
Weld examination Radiography in accordance with Section 9.
Pressure test Pressure test in accordance with Section 8.3.

ASTM A530/A530M is a separate general-requirements specification for certain steel pipe products; it is not another name for ASTM A691. The purchaser should follow the references and supplementary requirements in the applicable A691 edition rather than treating the two standards as interchangeable.

Manufacturing, Sizes and Weight

Manufacturing route

A typical EFW pipe manufacturing route includes plate inspection, plate cutting and edge preparation, forming, longitudinal seam welding with filler metal, the heat treatment required by the ordered class, sizing and end finishing, testing and final inspection. The qualified welding procedure, welding personnel qualifications and inspection requirements must comply with the applicable construction code, product specification and purchase order. Actual manufacturing steps and process controls should be documented in the manufacturer’s quality records.

ASTM A691 class designations

ASTM A691 provides multiple class designations. The following table summarizes the class groups; consult the applicable edition for the complete requirements:

 
Class group Designations
No heat treatment 10, 11, 12, 13
Stress relieved 20, 21, 22, 23
Normalized 30, 31, 32, 33
Normalized and tempered 40, 41, 42, 43
Quenched and tempered 50, 51, 52, 53

Within each group, the class number determines whether radiography and pressure testing are required. For example, Class 22 includes both radiography and the pressure test, whereas Class 20 does not. Always check the class table in the edition specified by the contract.

LONGMA product range

LONGMA’s listed round ASTM A691 pipe supply range is shown below. These are company supply dimensions, not the dimensional limits of the ASTM specification. Availability, material grade, class, wall thickness and length should be confirmed for the specific enquiry.

 
Item Company-stated range
Grade options 1Cr, 1-1/4Cr, 2-1/4Cr, 3Cr and 5Cr
LONGMA listed class options 12, 20, 21, 22, 30, 32, 40 and 50
Outside diameter 406.4–1422.2 mm (16–56 in.)
Wall thickness 7.92–75 mm
Length 3–18 m

ASTM A691 nominally covers pipe 16 in. (400 mm) outside diameter and larger, with wall thicknesses up to 3 in. (75 mm) inclusive. Other dimensions may be furnished if they comply with the specification’s requirements. The project order must identify the required dimensions and applicable tolerances.

Theoretical weight calculation

For an approximate theoretical mass per metre using a steel density of about 7,850 kg/m³, the commonly used metric formula is:

W = 0.02466 × t × (D − t)

where W is the approximate mass in kg/m, D is the outside diameter in mm and t is the nominal wall thickness in mm. For a pipe with an outside diameter of 610 mm and a wall thickness of 25 mm, the calculated value is approximately 360.65 kg/m. A 12 m length is therefore approximately 4,328 kg. This is an estimate based on the stated density; alloy composition, dimensional tolerances, end preparation and actual measured dimensions can affect the delivered mass. Use the manufacturer’s confirmed weight for shipping and commercial documentation.

Testing and Quality Documentation

Inspection and testing

The inspection and test plan should identify the tests required by the applicable ASTM A691 edition, the ordered class, supplementary requirements, construction code and purchaser specification. Depending on those requirements, records may include chemical analysis, tensile testing, visual and dimensional inspection, weld radiography, hydrostatic or other specified pressure testing, heat-treatment records and non-destructive examination. Do not substitute ultrasonic testing for radiography, or vice versa, unless the governing specification and purchaser explicitly permit the alternative.

Traceability and certificates

The pipe markings and documentation should maintain traceability to the plate heat and the relevant manufacturing and test records. The document package may include the material test certificate, heat-treatment records, weld examination reports, pressure-test records, dimensional reports and repair records as required by the order. Confirm the required inspection-document type before production. EN 10204 Type 3.2 is not simply a certificate signed by an unspecified third party; it involves validation by the manufacturer’s authorized inspection representative independent of the manufacturing department and the purchaser’s authorized inspection representative or the inspector designated by official regulations, as applicable to the standard and contract.

Third-party inspection

Where third-party inspection is required, define the inspection agency, scope, witness and hold points, notification periods, acceptance criteria and document review requirements in the inspection and test plan. The inspection arrangement should be agreed before production so that plate inspection, welding, heat treatment, examination and final release can be coordinated.

Applications and Material Selection

Where 2-1/4Cr Class 22 pipe may be specified

Chromium-molybdenum steels are used in elevated-temperature pressure equipment and piping applications where the design code and material selection process call for the relevant alloy grade. Potential project contexts include power-generation and refinery process systems. Whether ASTM A691 2-1/4Cr Class 22 is suitable for a particular steam line, heater circuit or process service must be determined by the design engineer using the design temperature, pressure, allowable stress, corrosion and hydrogen-damage considerations, fabrication requirements and applicable construction code. The product designation alone does not establish suitability for a specific service.

Comparison with other pipe specifications

 
Product specification Product form and general scope Selection note
ASTM A691 Electric-fusion-welded carbon and alloy steel pipe from pressure-vessel-quality plate for high-pressure, high-temperature service. Grade and class must be specified; Class 22 includes stress relief, weld radiography and pressure testing.
ASTM A672 Electric-fusion-welded steel pipe from pressure-vessel-quality plate for high-pressure service at moderate temperatures. The specific grade, class and design conditions govern; do not treat all A672 grades as interchangeable.
ASTM A213 Seamless ferritic and austenitic alloy-steel boiler, superheater and heat-exchanger tubes. A different product form and application scope from large-diameter A691 pipe.
ASTM A106 Seamless carbon steel pipe for high-temperature service. Not a direct material substitute for 2-1/4Cr alloy steel; design-code checks are required.
API 5L Line pipe for pipeline transportation systems. Its scope differs from A691 pressure piping; substitution requires engineering and purchaser approval.

Material selection must be based on the governing design code and service conditions. NACE MR0175/ISO 15156 should not be cited as a blanket approval for every 2-1/4Cr Class 22 product or service. Sour-service suitability requires evaluation of the actual material condition, hardness, environment, applicable part and specific requirements.

Procurement and Quotation Requirements

Build a complete RFQ

State the full product designation, including ASTM A691/A691M edition, 2-1/4Cr grade, Class 22, outside diameter, wall thickness, length, quantity, end preparation, design code and service conditions. Identify the required pressure test, radiography, supplementary examinations, impact testing if required, heat-treatment documentation, inspection-document type, third-party inspection and any purchaser-specific requirements. Clarify coating, marking, packaging, destination and delivery schedule where applicable.

Price and lead-time considerations

The quotation depends on plate grade and availability, pipe dimensions, quantity, forming and welding requirements, heat treatment, examination scope, testing, inspection, end preparation, documentation, packaging and freight. Stock availability and manufacturing lead time vary with the requested grade, class and dimensions. Confirm the delivery schedule and commercial delivery term in the written quotation rather than relying on a general estimate.

LONGMA manufacturing information

LONGMA states that its manufacturing site covers 230,000 square metres and annual output exceeds 500,000 tonnes. The company manufactures round ERW and LSAW steel pipes. For an ASTM A691 enquiry, confirm the required grade, class, dimensions, manufacturing route, inspection scope and availability directly with LONGMA. The technical and commercial offer should identify any requirements that need project-specific confirmation.

Conclusion

ASTM A691 2-1/4Cr Class 22 EFW pipe combines a chromium-molybdenum plate grade with a class designation that specifies stress-relief heat treatment, weld radiography and pressure testing. The grade and class must not be confused, and ASTM A530/A530M must not be described as another name for A691. A reliable procurement specification identifies the standard edition, grade, class, dimensions, service conditions, inspection scope and documentation requirements. Final material suitability remains subject to the project design code and engineering approval.

FAQ

What does Class 22 mean in ASTM A691?

Class 22 specifies stress-relief heat treatment, weld radiography in accordance with Section 9 and pressure testing in accordance with Section 8.3 of the applicable ASTM A691/A691M edition.

Is ASTM A691 the same as ASTM A530/A530M?

No. ASTM A691 is the product specification for EFW carbon and alloy steel pipe for high-pressure, high-temperature service. A530/A530M is a separate general-requirements specification.

What is the chemistry of 2-1/4Cr material?

The designation refers to nominal 2.25% chromium and 1.00% molybdenum alloy content. The full chemistry limits must be checked against the applicable plate specification and material certificate.

What sizes does LONGMA list for this product?

The source product information lists outside diameters of 406.4–1422.2 mm, wall thicknesses of 7.92–75 mm and lengths of 3–18 m. Confirm the required grade, class and dimensions for each order.

What should an RFQ include?

Specify the standard edition, grade, class, dimensions, quantity, design conditions, testing and examination scope, documentation level, inspection requirements and delivery information.

Request an ASTM A691 2-1/4Cr Class 22 EFW Pipe Quotation

Send LONGMA the required grade and class, outside diameter, wall thickness, length, quantity, design conditions, inspection scope and delivery destination. The enquiry can then be reviewed against the applicable ASTM A691/A691M requirements and project specification. Email: info@ilongma.com. Website: https://www.ilongma.com/.

Categories

Get Free Quote

Related Article​

Wechat ID: 008618661500134

Request Free Quote